dc.identifier.uri |
http://dx.doi.org/10.15488/762 |
|
dc.identifier.uri |
http://www.repo.uni-hannover.de/handle/123456789/786 |
|
dc.contributor.author |
Denkena, Berend
|
|
dc.contributor.author |
Brüning, J.
|
|
dc.contributor.author |
Niederwestberg, D.
|
|
dc.contributor.author |
Grabowski, R.
|
|
dc.date.accessioned |
2016-11-29T13:02:32Z |
|
dc.date.available |
2016-11-29T13:02:32Z |
|
dc.date.issued |
2016 |
|
dc.identifier.citation |
Denkena, Berend; Brüning, J.; Niederwestberg, D.; Grabowski, R.: Influence of Machining Parameters on Heat Generation during Milling of Aluminum Alloys. In: Procedia CIRP 46 (2016), S. 39-42. DOI: http://dx.doi.org/10.1016/j.procir.2016.03.192 |
|
dc.description.abstract |
Thin-walled components, i.e. fuselage frames of airplanes, are prone to an unstable process behavior during milling. Therefore, tools with a chamfer between the cutting edge and the flank face are often used for such machining tasks. During milling, the chamfered area comes into contact with the just cut surface. This contact leads to process damping forces and the induced heat into the workpiece in this contact zone is increased. Furthermore, the amount of induced heat depends on the process parameters. At certain spots on the machined surface this may lead to a local overheating, which can reduce stiffness significantly. When this occurs during milling of a thin-walled component, the component is often regarded as reject. In this paper, the influence of chamfers and process parameters on the induced heat into the workpiece is investigated experimentally. In addition, a simulation which predict the temperature in the workpiece in dependence of the process parameters is presented. |
eng |
dc.description.sponsorship |
Ministry of Economics, Labour and Transport of Lower Saxony/ZW3-80134969 |
|
dc.description.sponsorship |
DFG/DE 447/90-2 |
|
dc.language.iso |
eng |
|
dc.publisher |
Amsterdam : Elsevier |
|
dc.relation.ispartofseries |
Procedia CIRP 46 (2016) |
|
dc.rights |
CC BY-NC-ND 4.0 Unported |
|
dc.rights.uri |
https://creativecommons.org/licenses/by-nc-nd/4.0/ |
|
dc.subject |
milling |
eng |
dc.subject |
process damping |
eng |
dc.subject |
simulation |
eng |
dc.subject |
thermal behaviour |
eng |
dc.subject |
Cutting tools |
eng |
dc.subject |
Damping |
eng |
dc.subject |
Milling (machining) |
eng |
dc.subject |
Thin walled structures |
eng |
dc.subject |
Local overheating |
eng |
dc.subject |
Machining parameters |
eng |
dc.subject |
Process damping |
eng |
dc.subject |
Process parameters |
eng |
dc.subject |
simulation |
eng |
dc.subject |
Thermal behaviours |
eng |
dc.subject |
Thin walled components |
eng |
dc.subject |
Unstable process |
eng |
dc.subject |
Aluminum alloys |
eng |
dc.subject.classification |
Konferenzschrift |
ger |
dc.subject.ddc |
620 | Ingenieurwissenschaften und Maschinenbau
|
ger |
dc.title |
Influence of Machining Parameters on Heat Generation during Milling of Aluminum Alloys |
|
dc.type |
Article |
|
dc.type |
Text |
|
dc.relation.issn |
2212-8271 |
|
dc.relation.doi |
http://dx.doi.org/10.1016/j.procir.2016.03.192 |
|
dc.bibliographicCitation.volume |
46 |
|
dc.bibliographicCitation.firstPage |
39 |
|
dc.bibliographicCitation.lastPage |
42 |
|
dc.description.version |
publishedVersion |
|
tib.accessRights |
frei zug�nglich |
|