This thesis investigates back-contacted (IBC) bottom solar cells with passivating and carrier-selective
POLO contacts with three terminals (3T-POLO-IBC cell). Such cells form the
foundation of monolithic three-terminal tandem solar cells. This novel tandem solar cell
enables the use of sub-cells with mismatched photocurrents. Thus, this tandem solar cell
technology platform offers the flexibility with respect to subcell material selection, the ease
of fabrication, and a robustness to spectral variations of incident light over the course of
the day and year. Three building blocks of the 3T POLO IBC bottom solar cell, which are
based on each other, are examined: First, the passivating and carrier-selective POLO contact.
Second, the integration of POLO contacts on the rear side of a solar cell. Third, the principle
of operation of a bottom cell with three terminals.
In the first part, the process of charge carrier extraction at selective contacts to the photoabsorber
is theoretically explored. The selectivity of a contact is defined on the basis of
(reaction) kinetic considerations at the contact in terms of the rate ratio of desired processes
to undesired processes. The extraction efficiency of charge carriers at the contact is derived
as the ratio of the external voltage versus the internal voltage from a thermodynamic point of
view. To emphasize the unifying nature of the definitions in this thesis, the existing literature
definitions are calculated from the definitions in this thesis. The extraction efficiency is
related to the selectivity coefficient of the contact and the limiting efficiency of a silicon solar
cell with given contact selectivity is calculated accordingly. After the detailed theoretical
investigation on selectivity, the properties of n+ and p+ POLO contacts are examined. Low
saturation current densities between 2 fA/cm² and 18 fA/cm² and contact resistivities between
0.4mOhmcm² and 10mOhmcm² are found at the same time. It is shown that the efficient carrier
transport of majority carriers is ensured by pinholes in the interfacial oxide. The resulting
logarithmic selectivity coefficient of POLO contacts is determined to be above 15, which is
one of the highest values measured. This makes POLO contacts predestined for solar cells
with the highest efficiencies.
POLO contacts are integrated on the rear side of a back-contact cell with POLO contacts for
both polarities. Thereby, the p+ and n+ doped poly-Si on the backside of the solar cell form
a parasitic graded p+n+ junction within the defect-rich poly-Si with a carrier lifetime of a few
picoseconds. The arising recombination limits the achievable efficiency of the POLO-IBC cell
to about 18%. For this reason, the parasitic junction is removed during the cell fabrication
process by wet-chemically introducing a trench between the n+- and p+-doped poly-Si regions.
The POLO-IBC cell with isolated n+- and p+ poly-Si regions achieves a certified efficiency of
24.25%.
For the last part, a third POLO contact is added to the POLO-IBC cell and the 3T-IBC
bottom cell is studied in detail using current-voltage measurements. First, the different
realization options for a 3T tandem solar are sorted and the corresponding nomenclature is
presented. Two different 3T IBC bottom cell architectures are identified. The first one – the
unijunction bottom solar cell – contains a single minority carrier contact and two majority
carrier contacts. The second one – the bipolar junction bottom solar cell – on the other hand,
has two minority carrier contacts and a single majority carrier contact.
Both 3T bottom cell architectures are fabricated based on a modified POLO-IBC fabrication
process. The principles of operation and loss mechanisms are elucidated using J-V measurements
on illuminated devices and by means of analytical modeling. The experiments
show that the third contact of a 3T unijunction and bipolar junction bottom cell allows the
collection or injection of additional minority or majority carriers from or into the bottom
cell. Ideally, the power output of such a 3T bottom cell is nearly independent of the current
density applied by the top cell. Therefore, no current matching of both subcells is required.
However, the transport of majority carriers or minority carriers through the unijunction
or bipolar junction bottom cell causes a loss, which, however, can be made negligible by a
specific design of the bottom cell. The design rules are explained in detail. After the detailed
investigations, a 3T unijunction bottom cell with a textured n+-POLO front contact with an
efficiency of 20.3% and a simplified screen-printed PERC-like 3T bipolar junction bottom
cell with 14.4% are developed. The latter is an attractive approach to utilize the dominant
PERC technology in a low-cost tandem solar cell with maximum energy yield.
Finally, the first 3T GaInP//POLO-IBC tandem cell demonstrator is fabricated with an
efficiency of 27.3% and a net efficiency gain of 0.9% is demonstrated compared to the 2T
operation of the 3T tandem cell.
Die vorliegende Arbeit untersucht Rückkontakt-Bottomsolarzellen mit passivierenden und
ladungsträger-selektiven POLO-Kontakten mit drei Anschlüssen (3T-POLO-IBC-Bottomzelle).
Sie bilden das Fundament monolithischer Tandemsolarzellen mit drei Anschlüssen. Diese
neuartigen Tandemsolarzelle erlaubt die Verwendung von Subzellen, dessen Fotoströme
fehlangepasst sind. Damit bietet diese Tandemsolarzellen-Technologie Flexibilität bei der
Materialauswahl der Subzellen, einfache Herstellbarkeit und Robustheit gegenüber spektraler Änderung des einfallenden Lichts im Tages- und Jahresverlauf. Es werden drei aufeinander aufbauende Bausteine der 3T-POLO-IBC-Bottomsolarzelle untersucht: Erstens, der passivierende und ladungsträger-selektive POLO-Kontakt. Zweitens, die Integration von
POLO-Kontakten auf der Rückseite der Solarzelle. Drittens, die Funktionsweise einer Bottomzelle mit drei Anschlüssen.
Im ersten Teil wird der Prozess der Ladungsträgerextraktion an selektiven Kontakten zum
Fotoabsorber theoretisch ergründet. Die Selektivität eines Kontaktes wird auf der Grundlage
von (reaktions-) kinetischen Betrachtungen am Kontakt als das Ratenverhältnis gewollter
Prozesse zu ungewollten Prozessen definiert. Die Extraktionseffizienz von Ladungsträgern am Kontakt wird als das Verhältnis der externen Spannung gegenüber der internen Spannung aus thermodynamischen Gesichtspunkten abgeleitet. Um den vereinheitlichenden Charakter der Definitionen in dieser Arbeit hervorzuheben, werden die bestehenden Literatur-Definitionen aus den Definitionen in dieser Arbeit berechnet. Die Selektivität und Extraktionseffizienz werden miteinander korreliert und daraus der Wirkungsgrad einer Solarzelle mit vorgegebener Kontaktselektivität errechnet. Nach der detaillierten theoretischen Untersuchung der Selektivität werden die Eigenschaften von n+ und p+ POLO-Kontakten untersucht. Es werden niedrige Sättigungsstromdichten zwischen 2 fA/cm² und 18 fA/cm² und gleichzeitig Kontaktwiderstände zwischen 0,4 mOhmcm² und 10 mOhmcm² ermittelt. Es wird gezeigt, dass der effiziente Ladungsträgertransport der Majoritäten durch Pinholes im Grenzflächenoxid sichergestellt wird. Der resultierende logarithmische Selektivitäts-Koeffizient von POLO-Kontakten wird auf über 15 bestimmt. Damit gehören POLO-Kontakte zu den Kontakten mit der höchsten Selektivität und sind für Solarzellen mit höchsten Effizienzen prädestiniert.
Die POLO-Kontakte werden auf der Rückseite einer Rückkontaktzelle mit POLO-Kontakten
für beide Polaritäten integriert. Dabei formt das p+ und n+ dotierte Poly-Si auf der Rückseite
der Solarzelle einen parasitären, gradierten p+n+-Übergang im defektreichen Poly-Si mit
einer Ladungsträgerlebensdauer von wenigen Pikosekunden. Die resultierende Rekombination limitiert die erreichbare Effizienz der POLO-IBC-Zelle auf etwa 18%. Aus diesem Grund wird der parasitäre Übergang während des Zellherstellungsprozesses entfernt, indem ein Graben zwischen die n+- und p+-dotierten Poly-Si-Regionen nasschemisch eingebracht wird. Die POLO-IBC-Zelle mit isolierten n+- und p+-Poly-Si-Gebieten erzielt einen zertifizierten Wirkungsgrad von 24,25%.
Für den letzten Baustein wird die POLO-IBC-Zelle um einen dritten POLO-Kontakt ergänzt
und die 3T-IBC-Bottomzelle mittels Strom-Spannungsmessungen im Detail untersucht. Zuerst
werden die unterschiedlichen Realisierungsmöglichkeiten für eine 3T-Tandemsolar einsortiert und die dazugehörige Nomenklatur vorgestellt. Dabei werden zwei verschiedene 3T-IBC-Bottomzellen-Architekturen unterschieden. Eine Unijunction-Bottomsolarzelle enthält einen einzigen Minoritätsladungsträgerkontakt und zwei Majoritätsträgerkontakte. Eine Bipolar-Junction-Bottomsolarzelle hingegen hat zwei Minoritätsladungsträgerkontakte und einen einzigen Majoritätsladungsträgerkontakt. Beide 3T-Bottomzell-Architekturen werden auf Basis eines modifizierten Herstellungsprozesses für POLO-IBC-Solarzellen realisiert. Das Funktionsprinzip und die Verlustmechanismen werden mit Hilfe von J-V -Messungen an beleuchteten Bauelementen und mit Hilfe analytischer Modellierung untersucht. Die Experimente zeigen, dass der dritte Kontakt einer 3T-Unijunction- und Bipolar-Junction-Bottomzelle das Sammeln oder Injizieren von zusätzlichen Minoritäts- oder Majoritätsladungsträgern aus der oder in die Bottomzelle ermöglicht.
Im Idealfall ist die Leistungsabgabe einer solchen 3T-Bottomzelle nahezu unabhängig von
der Stromdichte, die von der Topzelle angelegt wird. Daher ist keine Stromanpassung beider
Subzellen erforderlich. Allerdings verursacht der Transport von Majoritätsladungsträgern
bzw. Minoritätsladungsträgern durch die Unijunction- bzw. Bipolar-Junction-Bottomzelle
hindurch einen Verlust, welcher jedoch durch eine gezielte Auslegung der Bottomzelle vernachlässigbar klein ausfallen kann. Die Auslegung wird im Detail erläutert. Schließlich wird eine 3T-Unijunction-Bottomzelle mit einem texturierten n+-POLO-Frontkontakt mit einem Wirkungsgrad von 20,3% und eine vereinfachte siebgedruckte PERC-ähnliche 3T-Bipolar-Junction-Bottomzelle mit 14,4% entwickelt. Letztere ist ein attraktiver Ansatz, um die
dominierende PERC-Technologie in einer kostengünstigen Tandemsolarzelle mit maximaler
Energieausbeute zu nutzen.
Abschließend wird der erste 3T-GaInP//POLO-IBC-Tandemzellen-Demonstrator mit einem
Wirkungsgrad von 27,3% hergestellt und ein Netto-Wirkungsgradgewinn von 0,9% im Vergleich zum 2T-Betrieb der 3T-Tandemzelle demonstriert.